Telesoft Intercom

(ALL Programming From Master extn. Only )

** 11 15 MDF21+FN+ MDF22+FN +MDF23+FN……

(Cut-Put Phone DOWN At END)

Example: 2-DIGITS Better write all MDF# Flexible# on paper first.

** 11 67 2 For 2 Digit DIALLING SYSTEMS

** 11 15 21 61

22 62

23 63

24 64

25 65 …… CUT AT END

Example: 3-DIGITS YOU MUST PROGRAM ALL MDF Nos..

** 11 67 3 For 3 Digit DIALLING SYSTEMS

** 11 15 21 701

22 702

23 703

24 704

25 705 …… CUT AT END

TeleDiary30- Program FLEXIBLE 2/3 DIGITS SETTING

** 11 67 2 FOR 2 DIGIT DIALLING (DEFAULT Nos ARE 21-36)

** 11 67 3 FOR 3 DIGIT DIALLING (DEFAULT Nos ARE 221-236)

** 11 67 3 FOR 3 DIGIT DIALLING (DEFAULT Nos ARE 221-236)

TeleDiary30 Master Extn Details

Master extn. = 22 For INTERCOM PAX 004/008/012/016 etc.

Master extn. = 22 For 1-TRUNK PBX 104/109/115/128 etc.

Master extn. = 23 For 2-TRUNK PBX 206/210/214/224+

Master extn. = 24 For 3-TRUNK PBX 308

Master extn. = 25 For Page+3-TRUNK PBX 316,320,324

(ALL Programming From Master extn. Only )

Answer-2 ** 81

** 11 12 (This will NOT reset Flexible Flat Program)

** 11 16

TeleDiary30- How to RESET FLEXIBLE Program

** 11 26 22222 FLAT Nos = MDF nos AS 21-36

CANCEL/STOP DOD "0" DIALING

** 11 80 1 EXT1 EX2 EX4 …………..cut at end

OPEN/ALLOW DOD "0" DIALING

** 11 80 2 EX1 EX2 EX3 ……………cut at end

OPEN/ALLOW STD "00" DIALING

** 11 80 7 EXT1 EX2 EX3 ………...…cut at end

TeleDiary30- Trunk In-Rings & Extn DOD/STD on 1st 2 Exts only

** 11 17 …...Very useful For Hotels

TRUNK-IN -SERVICES

** 11 70 0 TK1 TK2 TK3 ….……. cut at end

TRUNK-OUT OF -SERVICES

** 11 70 4 TK1 TK2 TK3…….. cut at end

** 11 73 TK EX1 EX2 EX3 EX4 Then you get dial tone

Note: If u want all rings on 1 ext only, then repeat same ext 4 times

**+11+66+0 …. Set System in Day MODE /**+11+66+2 for RINGS together on all

** 11 72 EX1 EX2 EX3

where EX1-forTK21 EX2-for-TK22 EX3-for-TK23 --- This is Comment

**+11+66+1 …. Set System in NIGHT MODE / **+11+66+6 for 8 RINGS on 1st Ex

CLI issues on Beetel C51 / M51 / i51 etc…

** 11 62 9 then CLI singnal before RING (For beetel c51/m51/i51)** 11 62 8 then CLI singnal after RING (default)

CLI issues on Panasonic phones - bcz it requires 4 Digits

** 11 62 5 then CLI singnal 4 digits (for Panasonic phones)

** 11 62 4 then CLI singnal 3 digits (default)

** 11 62 7 TRUNK CLI BEFORE RING (For Beetel C-51/ i51/M51 etc.)

** 11 62 6 TRUNK CLI AFTER RING (default)

Master extn. = 22 For INTERCOM PAX 004/008/012/016 etc.

Master extn. = 22 For 1-TRUNK PBX 104/109/115/128 etc.

Master extn. = 23 For 2-TRUNK PBX 206/210/214/224+

Master extn. = 24 For 3-TRUNK PBX 308, but Ex25- 316,324

Master extn. = 25 For Page+3-TRUNK PBX 316,320,324

Please …Read & follow very Important NOTES

NOTE 1 : ALWAYS DO FLEXIBLE PROG. FOR TRUNKs & OPERATOR-9 AS WELL.

NOTE 2 Better write all < MDF# Flexible# > on paper first, before Programing.

NOTE 3 : WHERE 'TK' STANDS For TRUNK Nos AND 'EX' STANDS For EXTn. Nos

NOTE 4 : For Intercom & 1-trunk Master Ext=22.For 2-trunk-23 3-trunk-24 P+3-trunk-25

NOTE 5 : ALL TK1 TK2… EX1 ..EX2.. ARE FLEXIBLE NUMBERS IF DONE ….

NOTE 6 While Flexible Programimg ALWAYS dial MDF# in 2-digits only (21-50...)

(ALL Programming From Master extn. Only )

**11+67+4 DIP 4 Reset All DIP OFF- ( DEFAULT is OFF )

**11+67+0 DIP-0 ON To Allow 1st digit-0 Flat Numbers.

**11+67+7 DIP-7 ON To Allow 1st digit-7 To access Trunk Line

**11+67+8 DIP-8 ON To Allow 1st digit-8 for Flat Numbers.

**11+67+9 DIP-9 ON To Allow 1st digit-9 for Flat Numbers.

*38 + EX EXTN TO HOTLINE(HL)

*36 EXTN DO NOT DISTURB(DND)

*33+EX EXTN CALL FORWARDING(CF)

*32 EXTN TO CANCEL ALL HL/DND/CF

9 Internal Call Operator/Reception FIXED on Extno.

*18 Internal Call Pickup

Talk+FL+Ex Internal Conference while talking then do Flash + Extno.

FLASH *13 Internal Call Barge-In while Busy tone then do FLASH *13

8/*18 Trunk Answer/Pickup & for Extn call Also

FLASH Trunk Hold+Music while on Trunk line Talking

FLASH 8 Trunk Hold Release while on Trunk line Talking

#7DD n...# Trunk Speed Dial Nos. in storage (From Master Extn only )

#8 DD Trunk Speed Dial from Memory storage

0 Trunk Access one by one which are IN-Service

21/22..etc. Trunk Access Selective - Dial on dial tone

*30+TK Trunk No. setting for me for Redial Only

*92 Trunk Redial on Trunk no. set by *30 above

*3 777 TRUNK In-Rings On Gate(Dial Tone)/On Operator(Busy Tone)

STEPS (ALL Programming From Master extn. Only )

SET FLEXIBLE PROG-3-STEPS (From Master extn. Only )

A ** 11 26 0 OPEN SESSION

B ** 11 15 MDF201+FN201 +MDF202+FN202 + ……so on

Put Phone DOWN at end

C ** 11 26 99999 CLOSE SESSION

Example: 3-Digits Better write all MDF# Flexible# on paper first.

A ** 11 26 0 B ** 11 15 201 601

202 602

203 603

204 604

205 701

206 702

207 703

208 704 …… CUT AT END

C ** 11 26 99999 OPEN SESSION

CLOSE SESSION

TeleSoft256- Program FLEXIBLE 3/4/5 DIGITS SETTING

FOR 3 DIGIT DIALLING ** 11 750 then ** 11 75 444444 (default 201 to 456)

FOR 4 DIGIT DIALLING ** 11 67 54 (default 0201 to 0456)

FOR 5 DIGIT DIALLING ** 11 67 55 (default 10201 to 10456)

TeleSoft256- Master Extns are….

Master extn. = 202 FOR INTERCOM STSTEM

Master extn. = 203 FOR 2-TRUNK STSTEM

Master extn. = 205 FOR 4-TRUNK STSTEM

Master extn. = 209 FOR 8/6-TRUNK STSTEM

STEPS (ALL Programming From Master extn. Only )

** 81 You get Dial Tone

** 11 12 You get Dial Tone

** 11 16 You get dial Tone Wait 5 seconds

TeleSoft256- How to RESET FLEXIBLE Program

A ** 11 26 0 OPEN SESSION

B ** 11 26 22222 Auto Session closed

NOTE: Now FLAT Nos = MDF# as 201-456

A ** 11 75 0 ( THEN ALSO DO **81 ) OPEN SESSION

B CANCEL/STOP DOD "0" DIALING

** 11 80 1 EXT1 EX2 EX3 ………….cut at end

B OPEN/ALLOW DOD "0" DIALING

** 11 80 2 EX1 EX2 EX3 ………….cut at end

B OPEN/ALLOW STD "00" DIALING

** 11 80 7 EXT1 EX2 EX3 ………….cut at end

C ** 11 75 99999 CLOSE SESSION

A ** 11 75 0 B TRUNK-IN -SERVICES WITH CLI TYPE DTMF

** 11 70 0 TK1 TK2 TK3 ….…..cut at end

B TRUNK-CLI TYPE FSK

** 11 70 1 TK1 TK2 TK3……..cut at end

B TRUNK-OUT OF -SERVICES

** 11 70 4 TK1 TK2 TK3……..cut at end

C ** 11 75 99999 OPEN SESSION

CLOSE SESSION

A ** 11 75 0 OPEN SESSION

B ** 11 73 TK EX1 EX2 EX3 EX4 Then you get dial tone

C ** 11 75 99999 CLOSE SESSION

Note: If u want ring on 1 ext only, then repeat same ext 4 times

<**11750> **+11+66+0 DayMODE (DM)<**117599999> /**+11+66+2 RINGS for all 4 ex

STEPS TeleDiary256- Trunk In-Rings & Extn DOD on 1st 2 Extns only

A ** 11 75 0 ** 11 17 ………...Very useful For Hotels

C ** 11 75 99999 OPEN SESSION

CLOSE SESSION

A ** 11 75 0 OPEN SESSION

B ** 11 72 EX1 EX2 EX3 EX4 ….

where EX1-forTK201 EX2-for-TK202 EX3-for-TK203 EX4-for-TK204

C ** 11 75 99999 CLOSE SESSION

<**11750> **+11+66+1 …. Set System in NIGHT MODE(NM)<**117599999>

CLI issues on Beetel C51 / M51 / i51 etc…

** 11 62 9 then CLI singnal after RING do for beetel c51/m51/i51

** 11 62 8 then CLI singnal before RING

CLI issues on Panasonic phones - bcz it requires 4 Digits

** 11 62 5 then CLI singnal 4 digits for Panasonic phones

** 11 62 4 then CLI singnal 3 digits

** 11 62 6 TRUNK CLI AFTER RING

** 11 62 7 TRUNK CLI BEFORE RING(For Beetel C-51/ i51/M51 etc.)

Master extn. = 202 FOR INTERCOM STSTEM

Master extn. = 203 FOR 2-TRUNK STSTEM

Master extn. = 205 FOR 4-TRUNK STSTEM

Master extn. = 209 FOR 8/6-TRUNK STSTEM

Please …Read & follow very Important NOTEs

: ALWAYS DO FLEXIBLE PROG. FOR TRUNKs & Master/OPERATOR-9 AS WELL.

: Better write all < MDF# Flexible# > on paper first, before Programing.

: WHERE 'TK' STANDS For TRUNK Nos AND 'EX' STANDS For EXTn. Nos

: For Intercom Master Ext=202, 2-trunk-203, 4-trunk-205, 8-trunk-209

: ALL TK1 TK2… EX1 ..EX2.. ARE FLEXIBLE NUMBERS IF DONE ….

While Flexible Programimg ALWAYS dial MDF# in 3-digits only (201-456)

(ALL Programming From Master extn. Only )

Reset All DIP OFF-( Default OFF ) < **11750> & <**1175 444444>

**11+67+90  — DIP-0 ON To Allow 1st digit-0 Flat Numbers.

 **11+67+97 — DIP-7 ON To Allow 1st digit-7 To access Trunk Line

 **11+67+99  — DIP-9 ON To Allow 1st digit-9 & 8 for Flat Numbers.

*38 + EX EXTN TO HOTLINE(HL)

*36 EXTN DO NOT DISTURB(DND)

*33+EX EXTN CALL FORWARDING(CF)

*32 9 Internal Call Operator/Reception FIXED on Extno.

*18 Internal Call Pickup

Talk+FL+Ex Internal Conference while talking then do Flash + Extno.

FLASH *13 Internal Call Barge-In while Busy tone then do FLASH *13

8/*18 : Trunk Answer/Pickup & for Extn call Also

FLASH : Trunk Hold+Music while on Trunk line Talking

FLASH 8 : Trunk Hold Release while on Trunk line Talking

#1DD n...# : Trunk Speed Dial Nos. in storage (From Master Extn only )

#3 DD : Trunk Speed Dial from Memory storage

0 : Trunk Access one by one which are IN-Service

*30+TK : 201/202…  : Trunk No. setting for me for Redial Only

*92 : Trunk Redial on Trunk no. set by *30 above

*3 777 : TRUNK In-Rings On Gate(Dial Tone)/On Operator(Busy Tone) N/DM